None SVE-3 Bedienerhandbuch PDF herunterladen (Seite 2)

Contact Local Building or Fire Officials about Restriction and Installation Inspections in you area as well as National Codes:

Please refer to appliance manufacturer's instructions to determine proper sizing and connection of venting system to appliance,

including maximum horizontal length, maximum height, and installation clearances (air spaces). The proper operation of the vent

system and appliance requires parts specified by Z-FLEX with no deletion or substitutions.

Z-FLEX recommends that an experienced professional who works with venting system on a regular basis perform the

installation. These instructions are intended as a guide to assist a professional installer.

When the Z-VENT system is installed, the following should be observed:

1. A venting system that exits the structure through a sidewall or the like, shall terminate not less than 12 inches (254 mm) above

the ground (see Illustration #2, Page 5)

2. The termination of a system shall be located above the snow line in geographical areas where snow accumulates. The termination

area should be kept clear of snow and ice at all times.

3. The vent shall not terminate less than 7 ft. (2.13m) above a paved sidewalk or driveway.

4. The termination shall be 6 ft. (1.8 m) or more from the combustion air intake of any appliance.

5. The system shall terminate more than 3 ft. (.91 m ) from any other building opening, gas utility meter, service regulator, or the like.

6. Exterior mounted venting systems should be enclosed below the roof line with a chase to limit condensation and protect against

mechanical failure.

NOTES:

A. The Z-FLEX SPECIAL STAINLESS VENT SYSTEM is for use only with appliances having a positive vent pressure of 8" of water

column or less.

B. Except for installation in one or two family dwellings, a venting system that extends through any zone above that on which the

connected appliances located shall be provided with an enclosure having fire resistance rating equal to or greater than that of the

floor or roof assemblies through which it passes.

C. Do not place any type of insulation in any required air spaces surrounding the vent system.

D. A termination must be used on all installations to assure proper operation and to prevent debris from entering the venting system.

E. The Z-Vent system must be free to expand and contract. Pipe must be properly supported. Vertical runs must us firestops as

lateral support at each ceiling level and at least one support collar at the base of the vertical run. For vertical runs exceeding 16'

(4.88 m), a support collar is required at 16' (4.88 ,m) intervals. Horizontal runs require a loose fitting metal strap or similar support

at each joint.

F. Examine all components for possible shipping damage prior to installation.

G. Proper joint assembly is essential for a safe installation. Follow these instruction exactly as written. Check severeness of joints

upon completion of assembly.

H. Check for unrestricted vent movement through walls, ceilings and roof penetrations.

I. Different manufacturers have different joint systems and adhesives. Do Not Mix Pipe, Fittings or Joining methods from

different manufacturers.

10 Foot Pipe

SPECIAL STAINLESS STEEL VENTING

For use with Category II, III, IV appliances

COMPONENT 3" SYSTEM CAT. # COMPONENT 3" SYSTEM CAT. #

SVEPWC0310 Adjust. Flashing SVSADJ03

Reducer 4" to 3"

SVSSCX03

GE106X

SVSRCX03

SVSLSX03

Flat Flashing

Locking Band

Firestop Support

Firestop Spacer

SVSTPX03

SVSACA03

SVEWMFA03

SVSERWC0403

SVSSCS03

SVSLBX03

SVSFSS03

SVSFSX03

SVSTTX03

SVSRTX03

WM CGI Starter

SVEPWC0308

Storm Collar

Z-Vent Sealant

WM Term Coupling

Ametek Fan Conn.

Termination Tee

Termination Box

Rain Cap

Top Support

2 Foot Pipe

1 Foot Pipe

6 Inch Pipe

90 Elbow

8 Foot Pipe

5 Foot Pipe

4 Foot Pipe

3 Foot Pipe

Vertical Drain Tee

Wall Thimble

WM GV Starter

SVEDTK

SVEVWC03

SVSWTX03

SVEWMG03

SVEEWC0390

SVEEWC0345

SVEDWC03Horizontal Drain Tee

45 Elbow

USA - National fuel gas code ANSI-Z223.1

CANADA - CAN/CGA-B149.1 or .2 Fuel Burning Installation Code

PARTS LIST

Drain Tube Kit

SVEPWC0305

SVEPWC0304

SVEPWC0303

SVEPWC0302

SVEPWC0301

SVEPWC03.5

- 2 -

1 2 3 4 5 6

Kommentare zu diesen Handbüchern

Keine Kommentare

None SVE-3 Bedienerhandbuch Seite 2

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Nein None SVE-3