None GB-2-K Bedienerhandbuch PDF herunterladen

Nudo Products, Inc.

1500 Taylor Avenue

Springfield, IL 62703

Phone 1.800.826.4132 * 1.217.528.5636

Fax 1.217.528.8722

Form 6013 Rev. 02 10/14

[email protected]

www.nudo.com

GroundBreaker™

Installation

Guidelines

6013

______________________________________________________________ Rev. 02 10/14

Please Read Disclaimers:

PLEASE READ ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION!!

These guidelines are provided in good faith to help prevent any problems caused by common

errors in installation. The manufacturer and/or distributor of this product shall not be held

responsible for installation actions taken or not taken. There are many details of installation that

are assumed to be general construction knowledge to experienced installers; which are no

included in these instructions. These installation guidelines are intended to be strictly

recommendations and are NOT to serve as a step-by-step, fail-safe installation checklist. Selection

of an experienced installer is the sole responsibility of the project owner and architect.

Nudo Products, Inc. does not accept any responsibility for job failure resulting from or associated

with improper site environmental conditions.

Safety Instructions:

When cutting or drilling, always wear protective glasses or

goggles and a face mask which covers the face and mouth.

Itching due to fibers may be avoided by the use of barrier

creams on exposed skin areas.

Tools Needed

 Circular saw with fine tooth carbide tipped saw

blade

 Hammer drill with masonry bits

 Trim Cutter

 Wire Brush

Materials Needed

 GroundBreaker™ Protection Liner 1', 2' or 4' x 50' Rolls

 3-inch Stainless Roofing Nails or Nylon Rivets 3/4" x 2"

 Hammer

 Heavy duty construction adhesive (optional)

 Trowel recommended by adhesive manufacturer

(optional)

 Personal protection equipment (goggles & mask)

 Tape measure

 Shovel

 Division, Corner Angles and J-Channel Trim

(optional)

Preparation:

Storage

All GroundBreaker™ Foundation and Insulation Protection Liner rolls

should be stored on a solid, flat, dry surface.

Prior to

Installation

Installation should NOT begin until you contact your utility company to

determine location of gas and power lines. Before installing remove

packaging materials. Allow the panels to acclimate to the temperature

and humidity for 48 hours before installing. Dig a trench 4" to 6" inches

down along-side the foundation. Placing the liner partially below grade will

help control energy loss.

Exterior Wall

Preparation

Now that the foundation is exposed, take a wire brush and remove any

dirt or loose particles from the foundation. This is extremely important if

you plan to use adhesive to fasten the liner to the insulation or foundation.

Please read adhesive manufacturers recommendation for further

1 2 3

Inhaltsverzeichnis

Seite 1 - GroundBreaker™

Nudo Products, Inc. 1500 Taylor Avenue Springfield, IL 62703 Phone 1.800.826.4132 * 1.217.528.5636 Fax 1.217.528.8722 Form 6013 Rev. 02 10/14 Info@

Seite 2 - Installation Steps

Nudo Products, Inc. 1500 Taylor Avenue Springfield, IL 62703 Phone 1.800.826.4132 * 1.217.528.5636 Fax 1.217.528.8722 Form 6013 Rev. 02 10/14 Info@

Seite 3 - Finish Work

Nudo Products, Inc. 1500 Taylor Avenue Springfield, IL 62703 Phone 1.800.826.4132 * 1.217.528.5636 Fax 1.217.528.8722 Form 6013 Rev. 02 10/14 Info@

Kommentare zu diesen Handbüchern

Keine Kommentare

None GB-2-K Bedienerhandbuch

Stöbern Sie online oder laden Sie Bedienerhandbuch nach Nein None GB-2-K herunter. none GB-2-K Instructions / Assembly Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Nein None GB-2-K